Beds with wooden sides are very comfortable and look beautiful on the site. Their main drawback is fragility, because such material quickly decays when it is in the soil. If you treat the boards before use, they will last much longer.
Birch and pine tar is an excellent natural antiseptic. If the wood is impregnated with it, it will be reliably protected from decay. It should be borne in mind that when treated with this substance, the surface of the board will remain sticky.
There are many specialty wood treatments available from hardware stores.
They all have good antiseptic properties and are easy to use.
It is better to choose the products that are recommended for outdoor use and have a water-repellent effect.
If you paint or varnish wooden sides, they will suffer less from soil moisture, which means they will not rot for a longer time.
For processing, tools intended for outdoor work are suitable.
They should be applied only on a dry surface, and the treated products should be used after the substance is completely absorbed.
You can protect a wooden surface with copper sulfate. To do this, prepare a solution of 100 g of the drug and 10 liters of warm water.Before applying vitriol diluted in water, the boards must be well dried, otherwise the product will quickly wash out, and the sides will soon rot.
Liquid glass is an aqueous-alkaline solution of potassium or sodium silicate. Such a tool is cheaper than paints and varnishes and special impregnations, and even surpasses them in efficiency. After application, liquid glass quickly hardens and becomes a reliable protection against moisture for a period of 8 to 10 years.
Used car oil is water-repellent and antiseptic.
You can get it at your nearest auto repair shop for almost free.
To make the boards last longer, you need to cover them with the composition several times. The only drawback of this substance is an unpleasant odor.
Firing wood is not only an effective, but also an absolutely environmentally friendly way to protect against decay. The procedure can be carried out with a blowtorch or gas torch.
The firing depth must be at least 1 mm.
After the end of the process, the boards need to be cleaned of soot, and to enhance the effect, the treated surface can be varnished. It is better to spend extra time preparing the sides than changing them every 2-3 years.
[Votes: 1 Average: 4]
* Review of the best according to the editorial board of expertology.ru. On the selection criteria. This material is subjective, does not constitute advertising and does not serve as a purchase guide. Before buying, you need to consult with a specialist.
Wood is a popular building material that is widely used in Russia. To increase the lifespan of wood, it must be carefully looked after. Special impregnations help to protect wooden structures from negative atmospheric influences, decay, the appearance of fungus, mold and insects. In addition, some formulations reduce the flammability of the material, making it fireproof. Products from different manufacturers are presented on the domestic market, each of them praises its own antiseptic. The advice of our experts will allow you not to make a mistake when choosing a composition.
Garden beds do not have to be boring and monotonous. See how beautiful the gardens are in these photos thanks to the shape of the beds.
They can be given a wide variety of configurations.
And decorative bumpers and borders can liven up the look of your garden like nothing else.
They can be made from any material at hand, including old planks, metal, brick, or stones.
The fence of the beds in the form of wattle is very beautiful. In order to prevent soil from spilling out of the box, agrofibre is placed under the sides on the inside.
Of course, there are a lot of simple ideas to tidy up and make the beds attractive. Simple improvised means will serve as the material for the fence. These can be leftovers from construction work, for example, slate or unnecessary things: barrels, buckets, tires, bottles.
Fencing made of corrugated board will serve for many years. The sheets bend well, so you can arrange the garden in an unusual way.
Take plastic or glass bottles as a building material. You will get not only a fence, but you can also get rid of debris, and the beds will sparkle with a new original look.
Match bottles of the same capacity and dig into the ground with the neck down. For strength, you can pour sand inside. To keep the design whimsical, paint the bottles in different bright colors. Next, you can see a photo of fences for the beds. We have selected the most popular and unusual design options. Now you understand that the beds are not just a piece of land. Use a border to make accents on the landscape design of the site. Create an unforgettable atmosphere in the country. Combine ideas and feel free to decorate.
The method of combining crops is very effective in practice if the companion plants are selected successfully. Therefore, the owners of the plots calculate according to a special table of the neighborhood of vegetables in the beds before planting. Some types of vegetables depress each other, others can improve the growth and development of neighbors, provide them with protection from pests.
When planning the beds, it is worth considering that companion plants give a greater yield if they are planted nearby.
Many summer residents note that due to the proximity of beans as a compaction for the garden bed where potatoes are grown, the number of the Colorado potato beetle is significantly reduced. Marigolds effectively protect cabbage from white butterfly. Despite this, a certain balance should be adhered to. After all, an excessive amount of marigolds in the garden can drown out the growth of cabbage.
Table of vegetable neighbors in the garden, creating a successful tandem:
|Vegetable name||Plants for a successful combination|
|strawberry||beans, spinach, marigolds, garlic, salad|
|kohlrabi||cucumber, lettuce, onion, beet|
|peas||carrots, corn, cucumber, calendula, eggplant|
|onion||tomato, celery, beetroot, savory, carrot|
|beans||potato, cucumber, tomato, strawberry, eggplant|
|cucumber||radish, pepper, peas, cabbage, beans|
|carrot||lettuce, onion, sage, tomato, peas|
|salad||strawberry, cucumber, carrot, radish|
|pepper||salad, cucumber, beans|
|a tomato||calendula, basil, beans, nasturtium, parsley|
Poor compatibility of planting vegetables in the garden is characterized by the following pairs of plants:
Even in a small area, you can get high yields by using the table of correspondence of neighboring plants when planting
A good example of the compatibility of vegetables in the garden is the combination of onions and carrots. How can an independent culture of onion give about 2.5 kg of yield from 1 m? beds. Carrots in the same area give about 6 kg of yield. When these crops are grown together with 1 m? you can get 9 kg of vegetables. These plants create protective barriers for each other from pests, so the efficiency of the area used increases.
Onions and carrots are great neighbors, so it is customary to plant them side by side.
Of course, when planning a joint cultivation of crops in the garden, you need to group the plants taking into account their height so that neither of them blocks the light for the other. This is necessary because vegetables can not only have different heights, but also grow at different rates. It is desirable that the seals that are planted additionally be lower in height than the main vegetables. The principle of the multi-tiered neighborhood of vegetables in the beds allows you to create favorable conditions for the root system of crops, and also contributes to the rational use of solar energy.
High yields are collected from the beds where beets and late cabbage are planted. To do this, on an area of 0.8x0.8 m, beets (9 plants) and cabbage (4 bushes) should be planted, not forgetting to fertilize the holes with a glass of compost and a handful of eggshells (pre-grind).
By planting marigolds near the beds, you can avoid some pests in the garden
To get an excellent result when planting beans and tomatoes, it is recommended to place the plants in a row with a step of 0.3 m. A drip irrigation system is installed along the row with bush beans so that each plant is at the dropper. Tomatoes are planted in the central part of the garden. As a result, the bean and tomato bushes should be staggered.
Correct planning of planting of vegetable crops is the key to a rich harvest
The crop rotation of the plants can also affect the yield of the beds. If the annual change of crops grown in the same bed is carried out in the correct order, the vegetable garden will produce good yields.
Benefits of correct crop rotation:
To increase yields and restore soil, green manure and crop rotation should be used.
The most primitive way of organizing crop rotation in the garden involves planting plants from different families on the same area every year. The easiest way to divide cultures into four groups is:
Table of the simplest crop rotation in the garden:
|The order of disembarkation by year||Recommended crops for planting|
|1st bed||2nd bed||3rd bed||4th bed|
To make it convenient to care for vegetable crops, they use a fence for the beds, with the help of which the grown plants are carefully separated from others. This increases yields and reduces the need for soil maintenance.
Fencing allows you to reduce the hassle of weeds by reducing the area available to them. Therefore, the need for regular weeding is reduced. By placing the bumpers deeper into the soil, less weeds will penetrate the cultivated soil.
In this case, the beds do not crumble. Owners of areas with loose and sandy soil face a similar problem. It is better to strengthen them with sides. The fence will not only look beautiful, but also become a practical solution.
In some cases, fencing is necessary.
This applies to warm beds, when layers of soil are poured into the made box. The sides are often used to fasten the arches of greenhouses in which flowers, greens and vegetables are grown for seedlings in spring. You can also plant indoor plants for the summer, and return flowers to the window in the fall.
If you place fences for the beds around the perimeter, they will look neat and civilized. This is very convenient when all types of plants are located separately from each other. Order will appear everywhere, and there will be no need to fight the weeds after every rain. It is enough just to keep the plants clean and water the plants with a minimum of effort.
The decoration of the beds is carried out from the remains of various materials. Wood, brick and stone are considered traditional. In order for the hedge to last a long time, you should carefully consider how to make a fence for the garden.
The fence made of it is very beautiful, but not durable. Most often, plots are fenced with boards. Bars, picket fence, lining and slab will cost more for fencing. Any kind of wood is appropriate.
You can make a fence from the branches that remain after cutting the trees. At first it will look quite elegant, but gradually the wooden fence will turn black and covered with fungus. If the sides are whitewashed, this will not give a good effect, since the whitewashing will gradually be washed off by the rains. The paint on the fence will also not help improve the appearance.
It will crack and begin to come off in layers.
By means of special treatment it is possible to renew the fence only for a short time. But after a few years, new ones will have to be installed to replace the old sides, since there will be cracks through which the soil will pour out. So this is not a good idea.
A good option is a brick that is placed diagonally. It was used as a fence for flower beds before. For beauty, you need to carefully and uniformly expose the bricks. The resulting flower bed will look elegant, especially if you whitewash or paint the fence. In this way, you can decorate a flower garden, garden paths.
It should be borne in mind that old bricks will not look attractive, and a decent amount will have to be spent on new material. The brick is laid out diagonally or in rows. Any flower girl can handle this simple job.
Slate is a roofing material. But it is not always used for its intended purpose. Sometimes a border for the beds is made from it. This is an economical option as you can build your own fence.
Slate sides have a neat appearance. To make them, you need to cut a sheet of slate into canvases of a certain length, and then bury it in the ground. In this way, you can get a high-quality decorative fence. Its appearance is enhanced with various paint colors. The only drawback is fragility and instability.
Placing the material in one layer can damage the edge that protrudes from the ground. In too soft soil, the plates will be skewed.
Also, slate will have to pay some attention after heavy rains, periodically correcting it.
The design of the sides is possible using a variety of cobblestones, pieces of flat slate. The difficulty lies in the fact that this is not a simple brick, the shape of which has already been given. In this case, you will have to make a little effort, select the stones by size, combine them with each other and fasten them with cement mortar. But as a result, you can get an almost eternal fence.
It should be borne in mind that if the fences for the beds are heavy, then the soil may subsequently sag.Therefore, the material cannot be installed without fixing, otherwise you will have to constantly monitor its condition.
Such fences for beds require little effort, and the result of the work will bring aesthetic pleasure. The fence for the garden is most often made of similar materials. As a rule, these fences can be seen in the country. However, over the years, new fences appear, the cost of which is slightly higher.
Fence for the garden from blocks
The longest service life and attractive appearance for garden fences, in the creation of which the manufacturer uses a wood-polymer composite. Photos of products made from it show all the aesthetics of such fences.
Unlike options from conventional wooden boards, WPC fencing has many advantages:
However, a decorative fence also has some disadvantages. WPC contains wood. Therefore, if the bed is constantly wet, then the liquid will gradually penetrate into the material. This will subsequently lead to the formation of mold.
Also, with prolonged exposure to ultraviolet rays, the destruction of the polymer occurs. To avoid this, you need to buy a protective impregnation and process the fence. For gardens, fences are made using decking.
You need to cut it into pieces of a certain size, fix a supporting structure to the garden bed and screw the board. The material is also used for the greenhouse, you can also fence the raspberry tree. Popular manufacturer - Mastersad.
You can buy decorative fences in the Leroy Merlin online store.
Fences can be made from any cheap or waste material. Most often, boards are used for this. You don't always need to buy them. As a rule, this improvised material always remains after repair. But you should not use low-quality boards to create a fence. They will quickly rot, and all the work will have to be done again.
Beds made of wood-polymer composite in the village
If the master used new boards to create the fence, this does not always guarantee a successful outcome. After a year, the wood will turn black and become overgrown with fungus. Therefore, it is advisable to give preference to WPC options.
This will avoid the annual painting of the boxes. Also, you do not have to make new fences every few years, which will save time and money.
There are many ideas for creating garden fences. Most often, wood is used, as for children's sandboxes, but there are more modern options.
Plastic beds in the city
The plastic fence is resistant to seasonal temperature changes. It does not absorb moisture and is not susceptible to the penetration of precipitation inside. Such a fence is easy to assemble and install.
Plastic garden bed
Given its affordability, it can be considered an ideal option for small beds and flower beds. The sides are selected depending on the required height and color preferences.
Plastic is not subject to rotting and burning. There are options for fencing that imitate wood, brick or stone. You can choose products for fencing sections or a solid area.
A popular building material is polycarbonate. Photos of fences from it show that it fits perfectly into landscape design. Its advantages are as follows:
The fence is relatively inexpensive. Such panels provide the convenience of fertilizing and digging the area.
A garden fence made of DSP is considered a practical option for arranging beds. Such strips are not destroyed under the influence of moisture, are resistant to combustion, and are environmentally friendly. They are easy to transport by folding them into the trunk of a car.
The material is also used for the repair of utility rooms and the construction of country furniture. Dimensions - 12x230x1250 mm.
It is framed by beds and flower beds. Such a fence is made of dense polyethylene and plastic with a thickness of 3 mm. The tape has a smooth and wavy shape. With its help you can:
The fence is easy to install. It will not last forever, but it is quite possible to count on 10-12 years without the need for replacement. The curb price depends on the size.
The metal fencing option is not entirely budgetary. Using 2mm sheets, you can make a sturdy border for your garden beds. It is undesirable to use ordinary metal, since thin plates quickly rust and turn into dust.
During the heat, the metal fence will quickly heat up, which will lead to constant drying out of the soil. This will negatively affect the growth and yield of the planted plants.
It is better to galvanize steel before use and use a polymer coating for the fence.
This is quite a suitable option, since the material will last a long time, maintain a given shape and will not suffer from temperature drops and high levels of humidity. But products made of aluminum and steel, as well as forged fences, are quite expensive.
However, despite the cost, such fences are used quite often. You can do it yourself. To do this, you will need the remains of simple metal no more than a millimeter thick.
Fencing requires some skill as thin plates are very unstable. They are more difficult to handle than wooden beams, and you can cut yourself while working. Such sides will stand for a relatively short time. On contact with the soil, the metal is corroded and degrades very quickly.
Polymer coated galvanized steel has a number of positive properties. Its appearance is attractive, and when exposed to sunlight, it does not heat up too much. If this material was used for the manufacture of boxes, then it will look neat.
The coated steel will withstand any climatic conditions. The material can be given any shape, the design is selected in a suitable size. Ready boxes are easy to assemble and disassemble. If you need to expand the bed, you can add the required volume.
The single-tiered fence is about seventeen centimeters high. Such a fence will reliably protect the site from various pests. To prevent dogs from entering the fence, the height should be increased.
The elements of the fence are equipped with stiffening ribs, which increases the strength of the structure. Most manufacturers guarantee that such products will last for several decades.
There are prefabricated decorative plastic fences that are produced in sections. They consist of several elements, each of which has a specific length. They are installed on the ground using special plastic pegs.
The appearance of such borders is similar to any other material. You can purchase a fence in the form of edged boards, small hemp, metal forging.
These models are more suitable for gardens, flower beds and small flower beds. Such fences are very expensive, so it makes no sense to install them for vegetable beds.
There are many videos on Youtube on how to make a fence at no extra cost. If you use plastic, then the costs will rise, especially with a large number of beds. But there is an option that can significantly reduce the cost of fencing.
A plastic bottle will come to the rescue. The use of empty containers is fairly common. It is used instead of pots even when transplanting flowers that adorn the windowsill.
The containers are selected of the same size, sand is placed inside. Bottles are placed upside down, after digging a small trench around the perimeter of the site.
To make the fence brighter and more original, it is covered with water-based paint. The bottles should stand at the same depth to get an even border. Most of the reviews show that this method is very beneficial.
If you need to form a fence for shrubs, you can use fittings and metal pipe scraps. Metal rods will need to be tied with wire or welded at the joints.
Such structures are durable and durable. They do not need to be cleaned for the winter, and can be quickly and inexpensively decorated any yard.
The elements of the fence are covered with paint to improve their appearance.
To create such beauty in your country house, you can use metal rods of any size. You can also take a pipe and cut it with a grinder. This will save on materials.
The wave of popularity of garden fences will never pass, because every owner wants to make his site more well-groomed and give it an aesthetic look. Arranging a garden and vegetable garden can be quite expensive, especially if you use metal fences.
The means at hand allow you to save your family budget. The most popular among them are plastic bottles, from which original fences for vegetable beds and flower beds are made. Any owner can cope with the process of creating such a border.
Although I have a cottage and a garden, I didn't think I was a gardener until I read the phrase "Gardeners in the country spend little, multiply plots and share obsessively."
It's true, but I was blind to the blindingly obvious! I was brainwashed with the chocolate box of an English cottage garden - billowing flowers and pastel colors, a carefully planned chaos of voluptuous beauty that requires meticulous attention to each individual plant to succeed. It could never be me - I'm too lazy!
But, as it turns out, this is far from the truth.
Country garden design pioneer Gertrude Jekyll in a small book "Beauties of the Country Garden Hardly mentions fruits, and vegetables don't drop in, as far as I remember. But the first dacha gardeners were not flower growers at all.
In the Middle Ages, poor English workers supplemented their meager wages with edible crops grown in their own gardens, usually vegetables such as kale and kale, onions and leeks, turnips, and peas and beans, which are dried and used as bases for a thick soup or stew known as 'chowder' (which, by the way, is where the word 'potager' comes from).
Along with these main vegetables, fruits such as apples, pears, cherries, plums and prunes, as well as strawberries will be grown. Various herbs were also needed for medicinal purposes. The pig and a few chickens will become part of the garden ecosystem, providing meat, eggs and fertility.
It is likely that, despite the hopeless conditions - or maybe because of them - some gardeners-summer residents were looking for beauty in their gardens along with all this productivity. Perhaps a strange self-sown violet or primrose was allowed to bloom to invigorate the spirits at the start of the year, or perhaps a particularly flowering honeysuckle or rose hip was dug and transplanted from a nearby hedge into the hedge of its own garden.
Over time, more and more flowers have been squeezed into odd corners to attract pollinators and contain less attractive weeds.
Pillars cut from a nearby forest or hedge will be used to support beans and peas, willow will be woven to create obstacles to keep pigs and chickens away from vulnerable plants, and any irreparably broken household items will be redone in one way or another. or another, in the garden. It would be almost unheard of to buy something exclusively for garden use!
As garden design from the continent came into vogue, wealthy gardeners began to grow a variety of local and non-native flowers delphiniums and roses, mallows and peonies, calendula, cornflowers, nasturtiums, sunflowers and more, as well as a wider range of vegetables, no doubt a few cuttings or seeds. from the large gardens of the estate "found their way" to the less stately gardens of the cottages!
When England flourished and ordinary workers found they had a little money and a little free time, they no longer depended so much on the edible and medicinal plants in their gardens. Gardeners began to allocate more and more space on the ground for flowers, presumably to say, "Look how I live - I have enough time and money to grow plants that no one can eat!"
It is often said that cottage gardens are not designed but evolve over time. Because a cottage garden reflects and represents the personality of the gardener, all cottage gardens are unique. One gardener may prefer mallow and hyssop spiers, and garlic or lavender for the edge paths, while another may prefer to grow bean stalks in a wigwam amid waves of sunflowers and cabbage. There are no forbidden plants if you like them or find them useful.
A dense planting suppresses weeds, but be prepared to intervene if necessary. For example, cut back anything that threatens to completely engulf nearby plants, or transplant self-sown annuals to a more favorable location if they grow exactly where you don't need them.
The style of the modern cottage garden is largely influenced by Gertrude Jekyll's ideas on how a cottage garden should look. While this species is undoubtedly attractive, it is much more dependent on a far-fetched sense of rural idyll than on the realities of past life.
Today, few of us are limited by the need to grow all our food on our own, although many of us try to grow at least some of the fruits, vegetables and herbs that will end up on our tables. It seems very bourgeois to grow a country garden just for flowers, but it would be silly to say that flowers have no value a blooming garden is a much-needed lifesaver for various insects, birds and other animals that live and feed among them.
It doesn't matter what you mean, if you are frugal with money but prodigal with plants, you can proudly call yourself a gardener in the country.